Three-Cabinet ADIX APS System

Three-Cabinet ADIX APS System
Installation
A three-cabinet system consists of an IX-CML common module and two IX-EXPML1 expansion modules. The IX-EXPML1 Expansion Module is used to add the second, third and fifth shelves to the ADIX APS. Use the IX-EXPML2 Expansion Module only when adding the fourth shelf.
The IX-EXPML1 expansion module provides the ADIX APS with six additional universal card slots. The first universal card slot provides 24 circuits on one highway. The second card slot provides 8 circuits on the same highway as the first card slot. The remaining 4 card slots each provide 16 circuits on two highways. An IX-PWSL power supply is required for each IX-EXPML1 installed.
Note 1: It is strongly recommended that the battery backup be connected to each shelf of a multi-shelved ADIX APS System.
Note 2: The setting of the CPUSW switch position 4 of on the IX-CPUP/HW card must be set to ON, when a IX-CPU20/ MEM-L is installed on the IX-CPUP/HW card.

Event message

Evt:210-YYYZ S4 Loopback test YYY on Trunk Cartridge Z has started
Evt:211-YYYZ S4 Loopback test YYY on Trunk Cartridge Z has stopped
Evt:220-3546 S4 the Sys admin log has been cleared by the DN (3546 in this case)
Evt:221-3546 S4 the Sys test log has been cleared by the DN (3546 in this case)
Evt:222-3546 S5 the DN (3546 in this case) enters the debugging facility that is password protected
Evt:255 S9 administered mode is not supported by the cartridge plugged into the slot
Evt:260-0302 S8 the ICS takes the access line on port 0302 out of service because no current was detected
Evt:261-0302 S1 the access line on port 0302 is returned to service after current was detected (see Evt:260)
Evt:263-302 S8 the ICS takes the E&M line on port 302 out of service because the far end did not respond to a disconnect signal
Evt:264-302 S1 the E&M line on port 302 is returned to service after the far end finally responded to a disconnect signal (see Evt:263)
Evt:265-302 S7 the E&M line on port 302 did not receive an expected wink signal or delay dial signal from the far end
Evt:267 S9 a data module has been disconnected
Evt:268-07 S8 Dialing filter 07 has lost data due to a fault in the system memory

BRI services and features

BRI services and features
• data transmission at speeds up to 128 kbps per loop, depending on the bandwidth supported by your service provider
• shared digital lines for voice and data ISDN terminal equipment
Norstar Basic Rate Interface (BRI) cards also support D-channel packet service between a network and terminal connection. This allows you to add applications such as point- of-sale terminals without additional network connections.
Any analog or digital network connections can be shared by all Norstar telephones, peripherals and applications, and ISDN terminal equipment (TE).
Modular ICS supports the following ISDN services and features offered by ISDN service providers:
• D-channel packet service (BRI only) to support devices such as transaction terminals. Transaction terminals are used to swipe credit or debit cards and transmit the information to a financial institution in data packets.
• calling number identification, which appears on both Norstar sets and ISDN terminal equipment with the capability to show the information
• Multi-Line Hunt or DN Hunting which switches a call to another ISDN line if the line usually used by the Network DN is busy. (BRI only)

BRI

BRI services and features
• data transmission at speeds up to 128 kbps per loop, depending on the bandwidth supported by your service provider
• shared digital lines for voice and data ISDN terminal equipment
Norstar Basic Rate Interface (BRI) cards also support D-channel packet service between a network and terminal connection. This allows you to add applications such as point- of-sale terminals without additional network connections.
Any analog or digital network connections can be shared by all Norstar telephones, peripherals and applications, and ISDN terminal equipment (TE).
Modular ICS supports the following ISDN services and features offered by ISDN service providers:
• D-channel packet service (BRI only) to support devices such as transaction terminals. Transaction terminals are used to swipe credit or debit cards and transmit the information to a financial institution in data packets.
• calling number identification, which appears on both Norstar sets and ISDN terminal equipment with the capability to show the information
• Multi-Line Hunt or DN Hunting which switches a call to another ISDN line if the line usually used by the Network DN is busy. (BRI only)

Door phone control boxes

DP5000, DKT3200, 3000 and 2000-series DKTs1 16 72 (40 Base Cabinet) (40/Expan. Cab.) 112 152 (72 Base Cabinet) (80/Expan. Cab.) 552 (72 Base Cabinet) (80/Expan. Cab.) IPT2000 telephones3 24 64 per cabinet 72 per system 160 per System 80 per cabinet 80 Base 80 Expansion 160 System 80 Base 80 Expansion 560 System IADM2020 on IPTs4 48 per system 2 IADM2020 per IPT 53 per cabinet 53 per system 58 per System 58 per cabinet 80 per cabinet 116 per system 80 per cabinet 400 per system DKT2204-CT or DKT2304-CT Cordless Telephone1 16 72 112 152 552 Door locks5 3 4 5 5 10 Door phone control boxes (DDCB) 2 2 3 3 8 Door phones 6 6 9 9 24 DSS consoles (DSS)

LCR

LCR Day of Week and Time Zone Setup
Program 528 – LCR Days of the Week Assignments
Use this program to assign each day of the week as a Weekday, Weekend or Holiday.
Program 529 – LCR Route Time Zone Assignments
Use this program to define Route Plan day types and time zones.
Program 527 – LCR Holiday Assignments
Use this program to assign which days of the year should follow LCR Holiday routing assignments.
LCR COS and Station Setup
Program 103 – Class of Service
Use this program to enable or disable LCR in COS feature sets.
Program 200 / 260– Station Data
Use this program to assign stations to COS feature sets and LCR station groups.

Lost Call Print-out

Lost Call Print-out
Description
ipLDK can provide information for calls that are terminated by the caller before answered or while on hold. The system will output records for these ‘Lost calls’ in real-time and will maintain a lost call summary count for on-demand reporting. Records indicate the CO line, called station, duration of ring, time and date as well as the type of call. The format of the individual call record is illustrated below with an explanation of the record.